Close Menu
    Facebook X (Twitter) Instagram
    Monday, May 19
    X (Twitter) LinkedIn
    All about Endpoint Management
    • Home
    All about Endpoint Management
    Home»Troubleshooting Issues»Common Errors/problems in computer’s & their identifications to resolve

    Common Errors/problems in computer’s & their identifications to resolve

    Eswar KonetiBy Eswar KonetiOctober 29, 8:36 pm4 Mins Read Troubleshooting Issues 182 Views
    Share
    Facebook Twitter LinkedIn Reddit

    There are lot of issues with Personnel laptop or desktop computer but you are not sure what that issue related.Here are am listing some of the problems which you might see in your day to day issues with PC’s also given their identification how to resolve it  🙂

    1. MONITOR LED IS BLINKING
    Check all the connections like Monitor Cable, Data cables, RAM, Display Card, CPU connections.

    2. CONTINUOS THREE BEEPS
    Problem in RAM Connection.

    3. THREE BEEPS ( 1 Long 2 Short)
    Problem in Display Card Connection

    4. THREE LONG BEEPS PERIOD WISE
    Problem in BIOS or RAM (Basic Input Output System)

    5. CONTINUOS NON-STOP BEEPING
    Key Board Problem (I.e.; Some Key is pressed for Longer time)

    6. FDD LED IS GLOWING CONTINUOSLY
    Data cable to be connected properly (twisted cable).

    7. NO DISPLAY ON THE SCREEN AT ALL
    Hard Disk cable connected wrongly. Connect rightly seeing the Red mark (Faces power supply) and then Restart.

    8. POWER LED IS OFF
    a. Check main power cord
    b. Check S.M.P.S.
    c. Check Mother Board connection

    9. SHOWING CMOS ERROR
    Replace 3 Volt battery of Mother Board . Set Original Settings Manually.(Refer CMOS Setup chart)
    Enter your search terms Submit search form

    10. SHOWING FDD ERROR OR FLOPPY DRIVE IS NOT WORKING PROPERLY
    Check Power cord of FDD, Data Cables, set CMOS & Finally the Check drive.

    11. SHOWING HDD ERROR OR HARD DISK FAILURE
    a. Check Power Cord
    b. Check connection of HDD
    c. Check Data cable
    d. Check Hard Disk parameters in CMOS or Auto detecting Setting Partitions by Fdisk Command, then format it to set track 0.

    12. MOTHER BOARD HANGS DUE TO UNSTABILIZED POWER SUPPLY
    a. Check S.M.P.S
    b. RAM not functioning properly.
    c. Software problem (due to using pirated software)
    d. CPU fan not functioning properly.

    13. DANCING SCREEN
    a. Check Display card connection
    b. Virus Problem
    c. Video Memory Problem

    14. SHAKING SCREEN
    a. Earthing problem
    b. Magnetic waves comes around.

    15. CPU CABINET SHOCK
    a. Check Earthing
    b. Check main power cord.

    16. NON-SYSTEM DISK ERROR
    a. Floppy Drive having different disk (Non-Bootable Disk) OR CMOS Parameters for Hard Disk may not be set properly.
    b. Hard Disk Partitions may not be created.
    c. Hard Disk may not be formatted.

    18. MISSING COMMAND INTERPRETOR
    May the file Command.com is corrupted OR Infected by Virus OR Someone has Erased it.

    19. SHOWING I/O ERROR
    a. The type of Hard Disk in CMOS may not be set properly.
    b. Operating system used for formatting is not valid

    20. SHOWING DIVIDE OVER- FLOW MESSAGE
    a. May some Directories or Files crash with other files.
    b. Use CHKDSK/F Command to correct it.

    21. HARD DISK MAKING NOISE WHILE PROCESSING
    a. Unstabilized power supply.
    b. Check for Loose Contact.
    c. Do not use Y Connectors for Hard Disk.
    d. It may create Bad Sector OR Weak Hard Disk.

    22. HARD DISK HANGS WHILE PROCESSING
    Check for Bad Sector by using CHKDSK or SCANDISK Command. If found format the Hard Disk and set Partition before that area.(This is the only procedure to use Hard Disk with Bad Sector) OR (To avoid Bad Sectors use Standard Power Supply)

    23. HARD DISK NOT DETECTED
    a. Check Power Connector
    b. Check Data Cables
    c. Check Jumpers

    24. PARTITION NOT SHOWN
    Operating System where the Hard Disk formatted is not supported with present Mother Board. For Eg: Hard Disk formatted with Pentium System will hide their partitions for 486 System.

    25. MMX/DLL FILE MISSING
    May the above files may be corrupted due to power failure or Virus. Make available above files from other Computer.

    26. WINDOWS REGISTRY ERROR
    This will happen due to sudden ON/OFF of the system. Final solution is to Reinstall Operating System.

    27. DISPLAY COLOUR DOES NOT MATCH
    a. Configure Display Card properly with their CD.
    b. The Standard setting for Windows is set it to 800x600 for better performance.

    28. UNKNOWN DEVICE FOUND
    May the Driver utility is not provided with operating system. Insert Driver CD and install software for the above Device. (Every Device requires driver utility to set active.

    Common Errors/problems in computer’s identifications to resolve PC Issues
    Share. Twitter LinkedIn Email Facebook Reddit

    Related Posts

    How to detect the source of registry key modifications on windows devices – Intune

    November 21, 8:49 pm

    Identifying devices managed by Intune but not reporting to WUfB using KQL

    November 09, 10:28 am

    Application Deployment with Hybrid Joined Requirement Rules in Intune

    October 06, 8:59 pm

    Leave a ReplyCancel reply

    This site uses Akismet to reduce spam. Learn how your comment data is processed.

    Sign Up

    Get email notifications for new posts.

    Author

    I’m Eswar Koneti ,a tech enthusiast, security advocate, and your guide to Microsoft Intune and Modern Device Management. My goal? To turn complex tech into actionable insights for a streamlined management experience. Let’s navigate this journey together!

    Support

    Awards

    Archives

    © Copyright 2009-2024 Eswar Koneti, All rights reserved.

    Type above and press Enter to search. Press Esc to cancel.